Jones 300 Sewing Machine Parts
New parts for your machine below. Choose a foot, belt, bobbin or needle, then check out with PayPal or card.
Jones 300 Replacement YDK Foot Control Pedal
Foot control to start, stop and vary sewing speed.
Jones 300 Bobbin Winder Ring Tyre
Replacement rubber ring for the bobbin winder.
Jones 300 Rubber Stretch Belt
Replacement drive belt to restore smooth machine running.
Jones 300 Motor, Belt & Foot Control Set
Foot control to start, stop and vary sewing speed.
Jones 300 Metal Bobbins x 10
Pack of 10 sturdy metal bobbins, ready to wind and sew.
Jones 300 Shuttle Hook
Replacement hook that forms the lockstitch with the bobbin thread.
Jones 300 2 Packets of 10 Organ Assorted Needles
Two packs of Organ needles in mixed sizes for everyday sewing.
Jones 300 Bobbin Case
Holds the bobbin and controls lower-thread tension.
Jones 300 Walking Foot & Guide & Instructions
Feeds thick layers evenly so seams stay matched. Guide and instructions included.
Jones 300 Ruffler / Pleating Foot
Creates neat gathers and pleats in one pass.
Jones 300 Zig Zag Presser Foot
Everyday foot for zig zag stitching and light decorative work.
Jones 300 Adjustable Invisible Zip Foot
Sews concealed zips close to the teeth for a tidy finish.
Jones 300 Adjustable Zip / Zipper Foot
Sews standard zips and edged trims right beside the teeth.
Jones 300 Hinged Teflon Zip Zipper Foot
Non-stick zip foot that slides over leather, vinyl and sticky fabrics.
Jones 300 Non-Stick Zig Zag Teflon Foot
Non-stick zig zag foot for leather, vinyl and other sticky fabrics.
Jones 300 Adjustable Sequins Ribbon Foot
Guides sequins, ribbon or braid so you can sew them on neatly.
Jones 300 Free Hand Embroidery / Darning Foot
For free-motion embroidery and darning with the feed dogs lowered.
Jones 300 Free Motion Embroidery / Quilting Foot
Large opening for free-motion embroidery, quilting and creative work.
Jones 300 Free Motion Quilting Foot - Open Toe
Open front gives a clear view while free-motion quilting.
Jones 300 Applique Foot
Clear view for applique work and satin-stitch edges.
Jones 300 Fringe Tailor Tacking Foot
Forms fringe loops and tailor tacks for marking or trim.
Jones 300 Roller Foot
Rolls over leather, vinyl and other fabrics that stick or drag.
Jones 300 3 Strand Multi Cording Foot
Holds up to three cords for neat decorative cording.
Jones 300 Adjustable Blind Stitch Foot
Sews almost invisible hems on skirts, trousers and curtains.
Jones 300 Bias Tape Binding Foot
Feeds bias tape so you can bind raw edges in one pass.
Jones 300 Gathering Foot
Gathers fabric as you sew — ideal for ruffles and fullness.
Jones 300 Bias Binder Binding Foot
Folds bias binding and stitches it onto the fabric edge.
Jones 300 5 Groove Pintuck Foot
Twin-needle pintucks with five grooves for neat spacing.
Jones 300 9 Groove Pintuck Foot
Twin-needle pintucks with nine grooves for finer spacing.
Jones 300 Button Hole Foot
Helps you sew neat, evenly sized buttonholes.
Jones 300 Button Sew On Foot
Holds the button steady while you stitch it in place.
Jones 300 Open Toe Buttonhole Foot
Open toe for a clear view when placing buttonholes.
Jones 300 Slide Buttonhole Foot
Sliding foot for measured buttonholes of a consistent length.
Jones 300 Open Toe Embroidery Foot
Open front so you can see clearly while embroidering.
Jones 300 Knit Foot
Helps feed stretch and knit fabrics with less puckering.
Jones 300 Overcast Edging Foot
Neatens raw edges with an overcast stitch to reduce fraying.
Jones 300 Multicord Foot 5 Hole
Guides up to five cords for decorative multi-cord stitching.
Jones 300 6mm Felling Foot
Forms neat flat-fell seams about 6mm wide.
Jones 300 Edge / Joining Stitch In A Ditch Foot
Joins fabric edges or stitches neatly in the ditch for binding and quilting.
Jones 300 4 x Red Sewing Machine Spool Pin Felts
Replacement red felts for spool pins on many Singer and other machines.